电加热反应釜

电加热反应釜省电操作

电加热反应釜效率高,环保无污染,但是耗电量大,运营成本高,如果大批量使用,建议改用循环导热油加热。

  • 产品价格:来电详谈:
  • 产品优势:坚固耐用不怕腐蚀,操作简单:
  • 产品包装方式:简单包装,包装物不回收:
  • 用途:化工生产:
  • 售后服务:全国质保一年:

电加热反应釜由于自身带有加热功能,不用额外配置加热设备,在相同功能下具有占地面积小、设备投资低等优势,是许多厂家优先考虑的设备。电加热反应釜是用电加热,虽然是环保无污染,但是用电的生产成本是最高的,许多厂家直呼电费很受伤,所以,节约用电就是每个电加热反应釜用户需要考虑的问题了。电加热反应釜的加热功率与反应釜的容积成正比,也就是说越大的反应釜,加热功率越高,耗电量也就越大。    电加热反应釜要想省电,首先在制作的时候就要注意。电加热反应釜不要用平盖的,反应釜下面是一个半圆的封头,顶部也要封头的,有没有压力要求的反应釜做成平顶的,就是上面是两扇盖的,这种反应釜最好是在盖的上面加一层保温棉,减少热量的流失。    其次是筒体保温,电加热反应釜在制作的时候,尽量要求外筒体的板厚要大于内筒体,这样热量会向里传递。同时要在外筒体上加保温棉,包括底下的封头也要加保温棉。出料管也要用保温棉包起来,有些地方由于气候比较冷,在物料从电加热反应釜里面流出来,经过出料管的时候就冷却凝固了,导致电加热反应釜内的物料流不出来,耽误生产。    第三是生产的时候不要停电动机,电动机在启动的时候电流是最大的,也是最耗电的,同时经常启动电动机也会造成电动机的损坏。电加热反应釜在运转的时候不允许带料启动,因为本来电动机启动的时候电流就大,如果再带料启动的话,启动电流就更大了,当电流超过电机的承受能力的时候,就会损坏。以上是对电加热反应釜省电的一些建议,欢迎大家留言补充。

Because of its own heating function, the electric heating reactor does not need additional heating equipment. It has the advantages of small area and low investment under the same function. It is the preferred equipment for many manufacturers. Electric heating reactor is heated by electricity, although it is environmentally friendly and pollution-free, but the production cost of electricity is the highest, many manufacturers call the electricity fee is very injured, so saving electricity is the problem that every user of electric heating reactor needs to consider. The heating power of the electric heating reactor is proportional to the volume of the reactor, that is to say, the larger the reactor, the higher the heating power, the greater the power consumption. In order to save electricity, we should pay attention to the production of electric heating reactor first. Electric heating reactor should not use flat cover, under the reactor is a semi-circular head, the top also has a head, there is no pressure requirements of the reactor made flat top, that is, the top is two covers, this kind of reactor is best to add a layer of thermal insulation cotton on the top of the cover, reduce heat loss. Secondly, the heat preservation of the cylinder body. When making the electric heating reactor, the thickness of the outer cylinder body should be greater than that of the inner cylinder body as far as possible, so that the heat can be transferred to the inside. At the same time, insulating cotton should be added to the outer cylinder, including the bottom head. The discharge pipe should also be wrapped with insulating cotton. In some places, because of the cold climate, the material flows out from the electric heating reactor, and then it cools and solidifies when passing through the discharge pipe, which leads to the material flow out of the electric heating reactor and delays production. Third, don't stop the motor in production. The current of the motor is the largest and the most power-consuming when it starts. At the same time, frequent starting of the motor will cause damage to the motor. Electric heating reactor in operation is not allowed to start with material, because the original motor starts when the current is large, if the material starts again, the starting current will be greater, when the current exceeds the bearing capacity of the motor, it will be damaged. Above are some suggestions for power saving of electric heating reactor. Welcome to leave a message to add.

  电加热反应釜效率高,环保无污染,但是耗电量大,运营成本高,如果大批量使用,建议改用循环导热油加热。